Sybase 11.0.3 For SCO UNIX 5.0.5安裝配置步驟(轉)
Sybase 11.0.3 For SCO UNIX 5.0.5安裝配置步驟(轉)[@more@]1.首先必須確定網路卡已正確地配置在系統上。
2.以root登入，用scoadmin命令建立Sybase使用者，組屬為Sybase
確定上述二部驟無誤之後，我們可以轉入一階段地安裝工作。
3.login:root
# divvy
系統 子分割槽表（試舉例）
+--------+------------+------+-+-----------+------------+
|Name |Type |New Fs|#|Fist Block | Last Block |
+--------+------------+------+-+-----------+------------+
|boot | EAFS |no |0|0 |19999 |
|swap | NON FS |no |1|20000 |109999 |
|root | HTFS |no |2|1100000 |709999 |
|/u | HTFS |no |3|7100000 |1309999 |
|raw1 | NON FS |no |4|－ |－ |
|raw2 | NON FS |no |5|－ |－ |
|recover | NON FS |no |6|2110454 |2110463 |
|hd0 | WHOLE DISK |no |7|0 |2111471 |
+--------+------------+------+-+-----------+------------+
raw1和raw2是Sybase的資料庫裝置實際存放的物理裝置名稱。raw1用來存放資料庫，raw2用來存放事務日誌。
在這裡我們正確地分配raw1和raw2的大小：
假設我們定義raw1=600M, raw2=200m。
nName or renawe a divishon
cCredit a new file system on this divison
tSelect or change filesystem type on new filesystem
pPrevent a new file system from being crented on the division
sStart a division on a different block
eEnd a division on a different block
rRestore the original division table
Enter you choice or q to Quit_____ n ↙
Whick division (o through 7)： 4 ↙
What do your want to call it?：raw1 ↙
定義起始塊，按需要設定起始塊：
Enter you choice or q Quit： S ↙
Whick division ? ：4 ↙
Start number block：1310000 ↙
（建議：boot 的大小為20MB，u檔案系統的大小為500MB）
同上，如此類推定義raw2後，螢幕應提示
+--------+------------+------+-+-----------+------------+
|Name |Type |New Fs|#|Fist Block | Last Block |
+--------+------------+------+-+-----------+------------+
|boot | EAFS |no |0|0 |19999 |
|swap | NON FS |no |1|20000 |109999 |
|root | HTFS |no |2|1100000 |709999 |
|/u | HTFS |no |3|7100000 |1309999 |
|raw1 | NON FS |no |4|1310000 |1910000 |
|raw2 | NON FS |no |5|1910001 |2110001 |
|recover | NON FS |no |6|2110454 |2110463 |
|hd0 | WHOLE DISK |no |7|0 |2111471 |
+--------+------------+------+-+-----------+------------+
Enter you choice or q to Quit q ↙
系統提示：
iInstall the division set_up shown
rRetarn to the previous menu
eexit without installing a division table
Enter your choice or q to Quit i ↙
然後，準備物理裝置raw1, raw2，在root下將raw1, rraw1, raw2, rraw2的屬性及組名更改為sybase，並且許可權為666
# cd dev ↙
# chown sybase raw* rraw* ↙
# chgrp sybase raw* rraw* ↙
# chmod 666 raw* rraw* ↙
然後退出以Sybase使用者登入系統
$ mkdir install ↙
$ cd install ↙
$ tar xv6 sco_kernel.scr ↙
把光碟插入CD_ROM將它安裝進檔案系統，以root登入。
# mount /dev/cd0 /mnt ↙
再次以Sybase使用者登入：
$ cd /mnt
$ sybload －D ↙
current directory is "/mnt"設定安裝的路徑
Is this the correct directory for installation?
If so, Please enter 'y' or 'n' : n ↙
Please specify the correct installation directory here
A null entry will terminate this installation: /u/sybase ↙
Current directory is "/u/Sybase"
Is this the correct directory for installation?
If so, Please enter 'Y' or 'Y' : y
設定安裝的方式：Is this a local or Remote in installation, as defined in your installation Guide?
Please enter L for Local or R for Remote.
> L ↙
Please enter the full name of the disk file of the global archive : > /mnt/sybimage ↙
Yor specified /mnt/sybimage for the media device, Is this correct? Please enter 'y' or 'Y' to continue: y
緊跟隨著系統將會提示你輸入Sybase產品的序列號（CAS）：
CAS：DVBYBY SOKOBY BYBYBD BYBKBK BZTWLO BJVL ↙
正確輸入序列號後，會提供一串可供安裝的選單項
選擇1：Sybase 11.0之後回車
可把光碟上的Sybase安裝至/u/Sybase之下。
至此，Sybase已安裝至硬碟上面，我們可以進行設定方面地工作。
$ pwd ↙ $/mnt
$ cd.. ↙ 退出mnt目錄。
首先, 要把在/mnt下的sybase拆卸掉,我們以root登入,執行# umount /dev/cd0 ↙ 即可
然後# cd /u/sybase/install ↙ “設定環境變數”
# SYBASE = /u/sybase; export SYBASE ↙
增大SHMMAX的大小
# 重新連結核心 sh ./sco_kernel.scr sybase ↙
# cd /etc/conf/cf.d ↙
# vi stune
刪掉MAXPMEM 0該行後，存檔退出
# vi mtune
修改NAIOHBUF該行，將50修改成500後，存檔退出
# cd /etc/conf/pack.d /itimer ↙
# cp space.c.presyb space.c ↙
# vi space.c
修改該行int alarm_accuracy設為等於-1；
# cd /usr/lib
# cp aiomemlock. presyb aiomemlock ↙
# vi aiomemlock （在該檔案末增加一行sybase 28000000）
# cd /etc/conf/sdevice.d
# vi aio
將該檔案重覆的兩行刪掉一行後，存檔退出
# vi suds
將suds該行的N，改為Y後存檔退出
# cd /etc/rc2.d
# vi S99*
在#字元下一行的行首加入一句： /etc/suds_ctrl -a 100
該100為Sybase的組號，做完此步之後
連結核心重新啟動後，重新進入Sybase使用者
$ cd install
$ sybinit
此時，請參考附頁1，將引數設定正確，提示安裝成功即可。
附頁1
注：在下文中每屏資訊由橫線隔開，在<>中在值為輸入值，MASTER裝置為raw1.
Sybase的主目錄為/u/sybase
SYBINIT
1. Release directory: /u/sybase
2. Edit / View Interfaces File
3. Configure a Server product
4. Configure an Open Client/Server product
5. Configure a Front End product
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <3>
----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
NEW OR EXISTING SQL SERVER
1. Configure a new SQL Server
2. Configure an existing SQL Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
ADD NEW SQL SERVER
1. SQL Server name:SYBASE
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the name of the new SQL Server (default is 'SYBASE'):
----------------------------------------------------------------------------
ADD NEW SQL SERVER
1. SQL Server name:SYBASE
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Incomplete
2. MASTER DEVICE CONFIGURATION Incomplete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 0
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
Enter the retry count (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the delay interval between retries (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port:
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the port number to use for this entry (default is ''):<7371>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port: 7371
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Is this information is correct?
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Modify or delete a service
Listener services available:
Protocol Address Port Name Alias
4. tcp credit.credit.COM 7371
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Write the changes to the interfaces file now?
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Incomplete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
----------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 29.299805
(建議：Master Device最好放在裸裝置/dev/rraw1下)
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
----------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 29.299805
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the size of the SQL sever's master device in megabutes：40
----------------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 40
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
---------------------------------------------------------------------------
SYBSYSTEMPROCS DATABASE CONFIGURATION
1. sybsystemprocs database size (Meg): 16
2. sybsystemprocs logical device name: sysprocsdev
3. create new device for the sybsystemprocs database: yes
4. physical name of new device:
5. size of the new device (Meg): 16
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<4>
Enter the physical device name for the sybsystemprocs database:
（建議：sybsystemprocs database放在裸裝置/dev/rraw2下）
---------------------------------------------------------------------------
SYBSYSTEMPROCS DATABASE CONFIGURATION
1. sybsystemprocs database size (Meg): 16
2. sybsystemprocs logical device name: sysprocsdev
3. create new device for the sybsystemprocs database: yes
4. physical name of new device: /u/sybase/data/sysprocs.dat
5. size of the new device (Meg): 16
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<4>
---------------------------------------------------------------------------
SET ERRORLOG LOCATION
1. SQL Server errlrlog: /u/sybase/install/errorlog
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
---------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<5>
---------------------------------------------------------------------------
SET THE SQL SERVER'S BACKUP SERVER
1. SQL Server Backuup Server name: SYB_BACKUP
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<6>
---------------------------------------------------------------------------
CONFIGURE LANGUAGES
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select the language you want to install, remove, or designate as the default
language.
Language Installed? Remove Install Make default
1. us_english yes no no yes
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<7>
---------------------------------------------------------------------------
CONFIGURE CHARACTER SETS
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select the character set you want to install, remove, or designate as the
default character set.
Character set Installed? Remove Install Make default
1. ASCII, for use with unsp yesno no no
2. Code Page 437, (United S nono no no
3. Code Page 850 (Multiling nono no no
4. ISO 8859-1 (Latin-1) - W yesno no yes
5. Macintosh default charac nono no no
6. Hewlett-Packard propriet nono no no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<8>
---------------------------------------------------------------------------
CONFIGURE SORT ORDER
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select a sort order.
SortOrder Chosen
1. Binary ordering, for the ISO 8859/1 or Latin-1 characterset set (is yes
2. General purpose dictionary ordering. no
3. Dictionary order, case insensitive, accent insensitive. no
4. Dictionary order, case insensitive. no
5. Dictionary order, case insensitive with preference. no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Complete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<9>
---------------------------------------------------------------------------
ACTIVATE AUDITING
1. Install auditing: no
2. sybsecurity database size (Meg): 5
3. sybsecurity logical device name: sybsecurity
4. creat new device for the sybsecurity database: no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Complete
9. ACTIVATE AUDITING Complete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Execute the SQL Server Configuration now?
---------------------------------------------------------------------------
Running task to create the master device.
Building the master device
...................................Done
Task to create the msster device succeeded.
Running task jto boot the SQL Server.
Task to boot the SQL Server succeeded.
Running task to create the sybsystemprocs database.
sybsystemprocs database created.
Task to created the sybsystemprocs database succeeded.
Running task to install system stored procedures.
............................................................................
.....................................................
Task to install system stored procedures succeeded.
Running task to set permissions for the 'model' database.
.Done
Task to set permissions for the 'model' database succeeded.
Running task to set the default character set and/or default sort order for the
SQL Server.
Setting the default character set to iso_1
Sort order 'binary' has already been installed.
Character set 'iso_1' is already is default.
Sort order 'binary' is already the default.
Task to set the default character set and/or default sort order for the SQL
Server succeeded.
Running task to set the default language.
Setting the default language to us_english.
Language 'us_english' is already the default.
Task to set the default language succeeded.
Configuration completed successfully.
Pressto continue.
-----------------------------------------------------------------------------
NEW OR EXISTING SQL SERVER
1. Configure a new SQL Server
2. Configure an existing SQL Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
-----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <2>
----------------------------------------------------------------------------
NEW OR EXISTING BACKUP SERVER
1. Configure a new Backup Server
2. Configure an existing Backup Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
ADD NEW BACKUP SERVER
1. Backup Server name:SYB_BACKUP
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
BACKUP SERVER CONFIGURATION
1. Backup Server errorlog: /u/sybase/install/backup.log
2. Enter / Modify Backup Server interfaces file information
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <2>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 0
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
Enter the retry count (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the delay interval between retries (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port:
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the port number to use for this entry (default is ''):<7372>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port: 7372
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Is this information is correct?
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Modify or delete a service
Listener services available:
Protocol Address Port Name Alias
4. tcp credit.credit.C 7372
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Write the changes to the interfaces file now?
----------------------------------------------------------------------------
BACKUP SERVER CONFIGURATION
1. Backup Server errorlog: /u/sybase/install/backup.log
2. Enter / Modify Backup Server interfaces file information
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Execute the Backup Server configuration now?
----------------------------------------------------------------------------
Running task to update the Backup Server runserver file.
Task jto update the Backup Server runserver file succeeded.
Running task to boot the Backup Serve.
waiting for server 'SYB_BACKUP' to boot...
Task to boot the Backup Server succeeded.
Configuration completed successfully.
Pressto continue.
-------------------------------------------------------------------------
NEW OR EXISTING BACKUP SERVER
1. Configure a new Backup Server
2. Configure an existing Backup Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ?Help
Enter the number of your choice and press return:
-----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
---------------------------------------------------------------------------
SYBINIT
1. Release directory: /u/sybase
2. Edit / View Interfaces File
3. Configure a Server product
4. Configure an Open Client/Server product
5. Configure a Front End product
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
Exiting.
The log file for this session is '/u/sybase/init/logs/log0613.024'.
2.以root登入，用scoadmin命令建立Sybase使用者，組屬為Sybase
確定上述二部驟無誤之後，我們可以轉入一階段地安裝工作。
3.login:root
# divvy
系統 子分割槽表（試舉例）
+--------+------------+------+-+-----------+------------+
|Name |Type |New Fs|#|Fist Block | Last Block |
+--------+------------+------+-+-----------+------------+
|boot | EAFS |no |0|0 |19999 |
|swap | NON FS |no |1|20000 |109999 |
|root | HTFS |no |2|1100000 |709999 |
|/u | HTFS |no |3|7100000 |1309999 |
|raw1 | NON FS |no |4|－ |－ |
|raw2 | NON FS |no |5|－ |－ |
|recover | NON FS |no |6|2110454 |2110463 |
|hd0 | WHOLE DISK |no |7|0 |2111471 |
+--------+------------+------+-+-----------+------------+
raw1和raw2是Sybase的資料庫裝置實際存放的物理裝置名稱。raw1用來存放資料庫，raw2用來存放事務日誌。
在這裡我們正確地分配raw1和raw2的大小：
假設我們定義raw1=600M, raw2=200m。
nName or renawe a divishon
cCredit a new file system on this divison
tSelect or change filesystem type on new filesystem
pPrevent a new file system from being crented on the division
sStart a division on a different block
eEnd a division on a different block
rRestore the original division table
Enter you choice or q to Quit_____ n ↙
Whick division (o through 7)： 4 ↙
What do your want to call it?：raw1 ↙
定義起始塊，按需要設定起始塊：
Enter you choice or q Quit： S ↙
Whick division ? ：4 ↙
Start number block：1310000 ↙
（建議：boot 的大小為20MB，u檔案系統的大小為500MB）
同上，如此類推定義raw2後，螢幕應提示
+--------+------------+------+-+-----------+------------+
|Name |Type |New Fs|#|Fist Block | Last Block |
+--------+------------+------+-+-----------+------------+
|boot | EAFS |no |0|0 |19999 |
|swap | NON FS |no |1|20000 |109999 |
|root | HTFS |no |2|1100000 |709999 |
|/u | HTFS |no |3|7100000 |1309999 |
|raw1 | NON FS |no |4|1310000 |1910000 |
|raw2 | NON FS |no |5|1910001 |2110001 |
|recover | NON FS |no |6|2110454 |2110463 |
|hd0 | WHOLE DISK |no |7|0 |2111471 |
+--------+------------+------+-+-----------+------------+
Enter you choice or q to Quit q ↙
系統提示：
iInstall the division set_up shown
rRetarn to the previous menu
eexit without installing a division table
Enter your choice or q to Quit i ↙
然後，準備物理裝置raw1, raw2，在root下將raw1, rraw1, raw2, rraw2的屬性及組名更改為sybase，並且許可權為666
# cd dev ↙
# chown sybase raw* rraw* ↙
# chgrp sybase raw* rraw* ↙
# chmod 666 raw* rraw* ↙
然後退出以Sybase使用者登入系統
$ mkdir install ↙
$ cd install ↙
$ tar xv6 sco_kernel.scr ↙
把光碟插入CD_ROM將它安裝進檔案系統，以root登入。
# mount /dev/cd0 /mnt ↙
再次以Sybase使用者登入：
$ cd /mnt
$ sybload －D ↙
current directory is "/mnt"設定安裝的路徑
Is this the correct directory for installation?
If so, Please enter 'y' or 'n' : n ↙
Please specify the correct installation directory here
A null entry will terminate this installation: /u/sybase ↙
Current directory is "/u/Sybase"
Is this the correct directory for installation?
If so, Please enter 'Y' or 'Y' : y
設定安裝的方式：Is this a local or Remote in installation, as defined in your installation Guide?
Please enter L for Local or R for Remote.
> L ↙
Please enter the full name of the disk file of the global archive : > /mnt/sybimage ↙
Yor specified /mnt/sybimage for the media device, Is this correct? Please enter 'y' or 'Y' to continue: y
緊跟隨著系統將會提示你輸入Sybase產品的序列號（CAS）：
CAS：DVBYBY SOKOBY BYBYBD BYBKBK BZTWLO BJVL ↙
正確輸入序列號後，會提供一串可供安裝的選單項
選擇1：Sybase 11.0之後回車
可把光碟上的Sybase安裝至/u/Sybase之下。
至此，Sybase已安裝至硬碟上面，我們可以進行設定方面地工作。
$ pwd ↙ $/mnt
$ cd.. ↙ 退出mnt目錄。
首先, 要把在/mnt下的sybase拆卸掉,我們以root登入,執行# umount /dev/cd0 ↙ 即可
然後# cd /u/sybase/install ↙ “設定環境變數”
# SYBASE = /u/sybase; export SYBASE ↙
增大SHMMAX的大小
# 重新連結核心 sh ./sco_kernel.scr sybase ↙
# cd /etc/conf/cf.d ↙
# vi stune
刪掉MAXPMEM 0該行後，存檔退出
# vi mtune
修改NAIOHBUF該行，將50修改成500後，存檔退出
# cd /etc/conf/pack.d /itimer ↙
# cp space.c.presyb space.c ↙
# vi space.c
修改該行int alarm_accuracy設為等於-1；
# cd /usr/lib
# cp aiomemlock. presyb aiomemlock ↙
# vi aiomemlock （在該檔案末增加一行sybase 28000000）
# cd /etc/conf/sdevice.d
# vi aio
將該檔案重覆的兩行刪掉一行後，存檔退出
# vi suds
將suds該行的N，改為Y後存檔退出
# cd /etc/rc2.d
# vi S99*
在#字元下一行的行首加入一句： /etc/suds_ctrl -a 100
該100為Sybase的組號，做完此步之後
連結核心重新啟動後，重新進入Sybase使用者
$ cd install
$ sybinit
此時，請參考附頁1，將引數設定正確，提示安裝成功即可。
附頁1
注：在下文中每屏資訊由橫線隔開，在<>中在值為輸入值，MASTER裝置為raw1.
Sybase的主目錄為/u/sybase
SYBINIT
1. Release directory: /u/sybase
2. Edit / View Interfaces File
3. Configure a Server product
4. Configure an Open Client/Server product
5. Configure a Front End product
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <3>
----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
NEW OR EXISTING SQL SERVER
1. Configure a new SQL Server
2. Configure an existing SQL Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
ADD NEW SQL SERVER
1. SQL Server name:SYBASE
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the name of the new SQL Server (default is 'SYBASE'):
----------------------------------------------------------------------------
ADD NEW SQL SERVER
1. SQL Server name:SYBASE
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Incomplete
2. MASTER DEVICE CONFIGURATION Incomplete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 0
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
Enter the retry count (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the delay interval between retries (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port:
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the port number to use for this entry (default is ''):<7371>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port: 7371
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Is this information is correct?
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYBASE
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Modify or delete a service
Listener services available:
Protocol Address Port Name Alias
4. tcp credit.credit.COM 7371
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Write the changes to the interfaces file now?
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Incomplete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
----------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 29.299805
(建議：Master Device最好放在裸裝置/dev/rraw1下)
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
----------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 29.299805
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the size of the SQL sever's master device in megabutes：40
----------------------------------------------------------------------------------
MASTER DEVICE CONFIGURATION
1. Master Device:
2. Size (Meg): 40
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Incomplete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
---------------------------------------------------------------------------
SYBSYSTEMPROCS DATABASE CONFIGURATION
1. sybsystemprocs database size (Meg): 16
2. sybsystemprocs logical device name: sysprocsdev
3. create new device for the sybsystemprocs database: yes
4. physical name of new device:
5. size of the new device (Meg): 16
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<4>
Enter the physical device name for the sybsystemprocs database:
（建議：sybsystemprocs database放在裸裝置/dev/rraw2下）
---------------------------------------------------------------------------
SYBSYSTEMPROCS DATABASE CONFIGURATION
1. sybsystemprocs database size (Meg): 16
2. sybsystemprocs logical device name: sysprocsdev
3. create new device for the sybsystemprocs database: yes
4. physical name of new device: /u/sybase/data/sysprocs.dat
5. size of the new device (Meg): 16
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Incomplete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<4>
---------------------------------------------------------------------------
SET ERRORLOG LOCATION
1. SQL Server errlrlog: /u/sybase/install/errorlog
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
---------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Incomplete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<5>
---------------------------------------------------------------------------
SET THE SQL SERVER'S BACKUP SERVER
1. SQL Server Backuup Server name: SYB_BACKUP
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Incomplete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<6>
---------------------------------------------------------------------------
CONFIGURE LANGUAGES
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select the language you want to install, remove, or designate as the default
language.
Language Installed? Remove Install Make default
1. us_english yes no no yes
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Incomplete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<7>
---------------------------------------------------------------------------
CONFIGURE CHARACTER SETS
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select the character set you want to install, remove, or designate as the
default character set.
Character set Installed? Remove Install Make default
1. ASCII, for use with unsp yesno no no
2. Code Page 437, (United S nono no no
3. Code Page 850 (Multiling nono no no
4. ISO 8859-1 (Latin-1) - W yesno no yes
5. Macintosh default charac nono no no
6. Hewlett-Packard propriet nono no no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Incomplete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<8>
---------------------------------------------------------------------------
CONFIGURE SORT ORDER
Current default language: us_english
Current default character set: ISO 8859-1 (Latin-1) - Westen European
8-bitcharacter set.
Current sort order: Binary ordering, for the ISO 8859/1 or Latin-1
character set (iso_1).
Select a sort order.
SortOrder Chosen
1. Binary ordering, for the ISO 8859/1 or Latin-1 characterset set (is yes
2. General purpose dictionary ordering. no
3. Dictionary order, case insensitive, accent insensitive. no
4. Dictionary order, case insensitive. no
5. Dictionary order, case insensitive with preference. no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Complete
9. ACTIVATE AUDITING Incomplete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<9>
---------------------------------------------------------------------------
ACTIVATE AUDITING
1. Install auditing: no
2. sybsecurity database size (Meg): 5
3. sybsecurity logical device name: sybsecurity
4. creat new device for the sybsecurity database: no
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
------------------------------------------------------------------------------
SQL SERVER CONFIGURATION
1. CONFIGURE SERVER'S INTERFACES FILE ENTRY Complete
2. MASTER DEVICE CONFIGURATION Complete
3. SYBSYSTEMPROCS DATABASE CONFIGURATION Complete
4. SET ERRORLOG LOCATION Complete
5. CONFIGURE DEFAULT BACKUP SERVER Complete
6. CONFIGURE LANGUAGES Complete
7. CONFIGURE CHARACTER SETS Complete
8. CONFIGURE SORT ORDER Complete
9. ACTIVATE AUDITING Complete
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Execute the SQL Server Configuration now?
---------------------------------------------------------------------------
Running task to create the master device.
Building the master device
...................................Done
Task to create the msster device succeeded.
Running task jto boot the SQL Server.
Task to boot the SQL Server succeeded.
Running task to create the sybsystemprocs database.
sybsystemprocs database created.
Task to created the sybsystemprocs database succeeded.
Running task to install system stored procedures.
............................................................................
.....................................................
Task to install system stored procedures succeeded.
Running task to set permissions for the 'model' database.
.Done
Task to set permissions for the 'model' database succeeded.
Running task to set the default character set and/or default sort order for the
SQL Server.
Setting the default character set to iso_1
Sort order 'binary' has already been installed.
Character set 'iso_1' is already is default.
Sort order 'binary' is already the default.
Task to set the default character set and/or default sort order for the SQL
Server succeeded.
Running task to set the default language.
Setting the default language to us_english.
Language 'us_english' is already the default.
Task to set the default language succeeded.
Configuration completed successfully.
Press
-----------------------------------------------------------------------------
NEW OR EXISTING SQL SERVER
1. Configure a new SQL Server
2. Configure an existing SQL Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
-----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <2>
----------------------------------------------------------------------------
NEW OR EXISTING BACKUP SERVER
1. Configure a new Backup Server
2. Configure an existing Backup Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <1>
----------------------------------------------------------------------------
ADD NEW BACKUP SERVER
1. Backup Server name:SYB_BACKUP
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
BACKUP SERVER CONFIGURATION
1. Backup Server errorlog: /u/sybase/install/backup.log
2. Enter / Modify Backup Server interfaces file information
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return: <2>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 0
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<1>
Enter the retry count (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 0
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the delay interval between retries (default is '0'): <3>
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<3>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port:
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:<2>
Enter the port number to use for this entry (default is ''):<7372>
----------------------------------------------------------------------------
EDIT TCP SERVICE
1. Hostname/Address: credit.credit.COM
2. Port: 7372
3. Name Alias:
4. Delete this service from the interfaces entry
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Is this information is correct?
----------------------------------------------------------------------------
SERVER INTERFACES FILE ENTRY SCREEN
Server name: SYB_BACKUP
1. Retry Count: 3
2. Retry Delay: 3
3. Add a new listener service
Modify or delete a service
Listener services available:
Protocol Address Port Name Alias
4. tcp credit.credit.C 7372
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Write the changes to the interfaces file now?
----------------------------------------------------------------------------
BACKUP SERVER CONFIGURATION
1. Backup Server errorlog: /u/sybase/install/backup.log
2. Enter / Modify Backup Server interfaces file information
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
Execute the Backup Server configuration now?
----------------------------------------------------------------------------
Running task to update the Backup Server runserver file.
Task jto update the Backup Server runserver file succeeded.
Running task to boot the Backup Serve.
waiting for server 'SYB_BACKUP' to boot...
Task to boot the Backup Server succeeded.
Configuration completed successfully.
Press
-------------------------------------------------------------------------
NEW OR EXISTING BACKUP SERVER
1. Configure a new Backup Server
2. Configure an existing Backup Server
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ?Help
Enter the number of your choice and press return:
-----------------------------------------------------------------------------
CONFIGURE SERVER PRODUCTS
Product Date Installed Date Configured
1. SQL Server Jun 09 96 14:35 Jun 13 96 17:30
2. Backup Server Jun 09 96 14:35 Jun 13 96 17:32
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
---------------------------------------------------------------------------
SYBINIT
1. Release directory: /u/sybase
2. Edit / View Interfaces File
3. Configure a Server product
4. Configure an Open Client/Server product
5. Configure a Front End product
Ctrl-a Accept and Continue, Ctrl-x Exit Screen, ? Help.
Enter the number of your choice and press return:
----------------------------------------------------------------------------
Exiting.
The log file for this session is '/u/sybase/init/logs/log0613.024'.
來自 “ ITPUB部落格 ” ，連結：http://blog.itpub.net/10617542/viewspace-949445/，如需轉載，請註明出處，否則將追究法律責任。
相關文章
- SCO5.0.5安裝步驟 (轉)
- 定製燒錄SCO UNIX安裝光碟的步驟(轉)
- SCO UNIX--安裝(轉)
- SCO UNIX安裝參考(轉)
- Sybase for linux安裝步驟Linux
- ORACLE 7.3.4 for SCO Unix 安裝說明(轉)Oracle
- SCO-UNIX在vmware下的安裝(轉)
- [精華] SCO UNIX安裝參考
- SCO UNIX學習寶典（系統安裝）(轉)
- SCO UNIX--基本配置及操作(轉)
- Sybase安裝配置
- SYBASE12.5.2 FOR REDHAT AS4.0 安裝步驟(zt)Redhat
- UNIX系統中安裝SAP的步驟
- AIX基本安裝步驟(轉)AI
- SCO UNIX學習寶典（基本配置及操作）(轉)
- PHPMemcache擴充套件安裝配置步驟PHP套件
- vnc安裝步驟，vnc安裝步驟詳解VNC
- TOMCAT的安裝步驟 (轉)Tomcat
- 轉：Linux、AIX UNIX、SCO UNIX下檢視硬體配置小結LinuxAI
- SCO UNIX 下裝置驅動程式開發 (轉)
- SCO UNIX 下裝置驅動程式開發(轉)
- SCO UNIX網路安全管理 (轉)
- NodeJS、NPM安裝配置步驟(windows版本)NodeJSNPMWindows
- xftp安裝步驟，xftp安裝的2大步驟FTP
- STF 安裝步驟
- php安裝步驟PHP
- oracle 安裝步驟Oracle
- [ 安裝 ] Zeppelin安裝步驟！
- DKhadoop環境安裝配置步驟詳解Hadoop
- SCO UNIX 一些經驗(轉)
- 在SCO UNIX系統中使用另一unix硬碟(轉)硬碟
- windows安裝cnpm步驟WindowsNPM
- zookeeper安裝部署步驟
- Iris 框架安裝步驟框架
- anaconda安裝步驟
- Linux 安裝步驟Linux
- Nagios安裝步驟iOS
- charles的安裝步驟