Windows徽標認證Requirement和Policy更新
代理公司
Windows徽標認證團隊提醒各位合作伙伴下列的Requirement和Policy已經更新。您可以在Winqual 網站()上的LogoPoint中獲取詳細內容。
新的Requirement
下列為新增的Requirement,需要您提供意見反饋:
• GRAPHICS-0083. Graphics - Additional Qualifications - Cold Tuning.
• STREAM-0091. Tuner- Additional Qualifications - Hybrid/Combo Implementation.
• STREAM-0092. Tuner- Additional Qualifications - Signal Quality and Signal Lock Test Suite.
• CONNECT-0132. USB 3.0 hubs properly implement the SuperSpeed hub descriptor, standard SuperSpeed Descriptors, and the USB 2.0 ports in USB 3.0 hubs report version 2.1.
• CONNECT-0133. USB 3.0 hubs map their ports as defined in section 10.1 of the USB 3.0 specification.
• CONNECT-0134. USB 3.0 Hub should always report the port status bits correctly, as per the USB spec.
• CONNECT-0135. In the scenario where SuperSpeed termination was disabled and device has been enumerated on 2.0 port, if the software enables the SuperSpeed and then resets the 2.0 port, device should correctly move over.
• CONNECT-0136. USB 3.0 Hubs should not turn off SuperSpeed termination on downstream ports on over-current and port reset.
• CONNECT-0137. USB hubs support suspend, and downstream devices should not fall off the bus when the hub resumes from selective suspend.
• CONNECT-0138. USB Hubs correctly report whether they are bus or self-powered.
• CONNECT-0139. All USB devices must enumerate and operate on EHCI and xHCI controllers as well as downstream of full speed, a high speed and SuperSpeed USB hubs.
• CONNECT-0140. Devices should signal attach within 500ms after system resumes. If the hub lost power during system suspend, this interval will be calculated from the time hub has powered on the port.
• CONNECT-0141. If the upstream SuperSpeed termination is on, devices should always connect on the 3.0 port and never connect on the 2.0 port.
• CONNECT-0142. USB devices should not disconnect from the upstream port while going to or resuming from selective suspend.
• SYSFUND-0230. Desktop and All-In One systems with Ethernet devices must implement network presence conform to the Power Management specification on the NDIS Program and Wake on LAN patterns.
• SYSFUND-0229. Systems with a greater than 2.2 terabyte boot drive must comply with UEFI specification.
• SYSFUND-0228. Server systems supporting RemoteFX must meet requirements.
• GRAPHICS-0082. Graphics device intended for use with RemoteFX must meet requirements.
• DEVFUND-0047. Drivers must support all PnP IRPs.
已停用的Requirement
下列的Requirement已經停用。請參見各項Requirement的詳細內容以取得停止使用的日期。
• GRAPHICS-0059
• NETMEDIA-0039
• NETMEDIA-0012
• NETMEDIA-0057
• NETMEDIA-0075
• DISPLAY-0113
• All MODEM requirements
• NETWORK-0141, 0142, and 0143 (Winsock Direct)
• NETWORK-0026, 0027, 0029, 0030, 0033, 0130, 0131, 0132 (ISDN)
• CONNECT-0025, 0026, 0027, 0028, 0029 (IrDA)
• DISPLAY-0103, 0106, 0107, 0108, 0109, 0110 and SYSFUND-0138 (Sideshow)
• GRAPHICS-0014
• GRAPHICS-0068
• SYSFUND-0211
• STORAGE-0004
• STORAGE-0017
• BUSPORT-0020
• GRAPHICS-0021
• DISPLAY-0112
• SYSFUND-0218
• DISPLAY-0063
• DISPLAY-0095
已更新的Requirement
下列Requirement均已更新:
• GRAPHICS-0010. Restructure of details.
• CONNECT-0120. Republished.
• NETMEDIA-0002. Clarification.
• NETMEDIA-0008. Added "if-implemented."
• NETMEDIA-0011. Added "if-implemented."
• NETMEDIA-0017. Reworded exception.
• NETMEDIA-0021. Minor edits.
• NETMEDIA-0022. Clarification.
• NETMEDIA-0026. Clarification.
• NETMEDIA-0029. Clarification.
• NETMEDIA-0032. Clarification.
• NETMEDIA-0036. Removed "if-implemented," added clarification.
• NETMEDIA-0037. Clarification, added exception.
• NETMEDIA-0043. Clarification.
• NETMEDIA-0047. Removed "if-implemented," clarified exception.
• NETMEDIA-0049. Clarification.
• NETMEDIA-0053. Added regional profiles, clarified exceptions.
• NETMEDIA-0054. Removed "if-implemented."
• NETMEDIA-0059. Clarification.
• NETMEDIA-0060. Changed to "if-implemented."
• NETMEDIA-0061. Clarification.
• NETMEDIA-0066. Removed "if-implemented," added exception.
• NETMEDIA-0078. Changed to "if-implemented."
• PORTABLE-0036. Clarification.
• NETMEDIA-0001. Clarification.
• NETMEDIA-0003. Clarification.
• NETMEDIA-0008. Clarification.
• NETMEDIA-0018. Exemption clarified.
• NETMEDIA-0041. Clarification.
• NETMEDIA-0042. Clarification.
• NETMEDIA-0048. Clarification.
• NETMEDIA-0050. Clarification.
• NETMEDIA-0051. Clarification.
• NETMEDIA-0062. Clarification.
• NETMEDIA-0070. Clarification.
• NETMEDIA-0071. Clarification.
• NETMEDIA-0072. Clarification.
• STREAM-0084. Fixed typo.
• BUSPORT-0041. Changed effective date to June 1, 2012.
• SYSFUND-0192. Clarified intent on allowing only Windows 7 logo drivers on Windows 7 systems.
• CONNECT-0123. Clarified meaning of "alternate."
• NETWORK-0212. Changed effective date to January 1, 2011 for client devices.
• NETWORK-0227. Changed effective date to January 1, 2011. Added clarification.
• BUSPORT-0045. Deleted portion of text about CSZ bit.
• DEVFUND-0039. Fixed typo.
• DEVFUND-0048. Clarification.
• STORAGE-0026. Clarification.
• CONNECT-0034. Deleted section 5.
• BUSPORT-0042. Changed effective date to June 1, 2012.
• DISPLAY-0069. Restructured for clarity.
• GRAPHICS-0007. Restructured for clarity.
• GRAPHICS-0015. Updated title and added details.
• GRAPHICS-0031. Restructured for clarity.
• GRAPHICS-0036. Restructured for clarity.
• GRAPHICS-0071. Restructured for clarity.
• DISPLAY-0105. Added detail to design notes section.
• GRAPHICS-0074. Added detail to the WDDM driver checklist.
• GRAPHICS-0075. Added second paragraph.
• STORAGE-0001. Changed end of life for Medium Changer and Tape programs to June 1, 2010.
• STORAGE-0003. Clarifications, changed end of life for Medium Changer and Tape programs to June 1, 2010.
• STORAGE-0024. Updated note, superseded STORAGE-0017.
• STORAGE-0006. Clarification.
• STORAGE-0007. Clarification.
• BUSPORT-0019. Combined with BUSPORT-0020.
• DISPLAY-0111. Does not apply to network projectors. Text clarification.
• GRAPHICS-0016. Updated minimum color depth to 32 bpp.
• STREAM-0082, 0083, 0084, 0085. Changed enforcement date to December 1, 2010.
• INPUT-0067. Deleted references to Terminal Services.
• SYSFUND-0009. Same change as GRAPHICS-0016.
• SYSFUND-0185. Updated for Windows Home Server V2.
• GRAPHICS-0023. Restructured for clarity.[@more@]
Windows徽標認證團隊提醒各位合作伙伴下列的Requirement和Policy已經更新。您可以在Winqual 網站()上的LogoPoint中獲取詳細內容。
新的Requirement
下列為新增的Requirement,需要您提供意見反饋:
• GRAPHICS-0083. Graphics - Additional Qualifications - Cold Tuning.
• STREAM-0091. Tuner- Additional Qualifications - Hybrid/Combo Implementation.
• STREAM-0092. Tuner- Additional Qualifications - Signal Quality and Signal Lock Test Suite.
• CONNECT-0132. USB 3.0 hubs properly implement the SuperSpeed hub descriptor, standard SuperSpeed Descriptors, and the USB 2.0 ports in USB 3.0 hubs report version 2.1.
• CONNECT-0133. USB 3.0 hubs map their ports as defined in section 10.1 of the USB 3.0 specification.
• CONNECT-0134. USB 3.0 Hub should always report the port status bits correctly, as per the USB spec.
• CONNECT-0135. In the scenario where SuperSpeed termination was disabled and device has been enumerated on 2.0 port, if the software enables the SuperSpeed and then resets the 2.0 port, device should correctly move over.
• CONNECT-0136. USB 3.0 Hubs should not turn off SuperSpeed termination on downstream ports on over-current and port reset.
• CONNECT-0137. USB hubs support suspend, and downstream devices should not fall off the bus when the hub resumes from selective suspend.
• CONNECT-0138. USB Hubs correctly report whether they are bus or self-powered.
• CONNECT-0139. All USB devices must enumerate and operate on EHCI and xHCI controllers as well as downstream of full speed, a high speed and SuperSpeed USB hubs.
• CONNECT-0140. Devices should signal attach within 500ms after system resumes. If the hub lost power during system suspend, this interval will be calculated from the time hub has powered on the port.
• CONNECT-0141. If the upstream SuperSpeed termination is on, devices should always connect on the 3.0 port and never connect on the 2.0 port.
• CONNECT-0142. USB devices should not disconnect from the upstream port while going to or resuming from selective suspend.
• SYSFUND-0230. Desktop and All-In One systems with Ethernet devices must implement network presence conform to the Power Management specification on the NDIS Program and Wake on LAN patterns.
• SYSFUND-0229. Systems with a greater than 2.2 terabyte boot drive must comply with UEFI specification.
• SYSFUND-0228. Server systems supporting RemoteFX must meet requirements.
• GRAPHICS-0082. Graphics device intended for use with RemoteFX must meet requirements.
• DEVFUND-0047. Drivers must support all PnP IRPs.
已停用的Requirement
下列的Requirement已經停用。請參見各項Requirement的詳細內容以取得停止使用的日期。
• GRAPHICS-0059
• NETMEDIA-0039
• NETMEDIA-0012
• NETMEDIA-0057
• NETMEDIA-0075
• DISPLAY-0113
• All MODEM requirements
• NETWORK-0141, 0142, and 0143 (Winsock Direct)
• NETWORK-0026, 0027, 0029, 0030, 0033, 0130, 0131, 0132 (ISDN)
• CONNECT-0025, 0026, 0027, 0028, 0029 (IrDA)
• DISPLAY-0103, 0106, 0107, 0108, 0109, 0110 and SYSFUND-0138 (Sideshow)
• GRAPHICS-0014
• GRAPHICS-0068
• SYSFUND-0211
• STORAGE-0004
• STORAGE-0017
• BUSPORT-0020
• GRAPHICS-0021
• DISPLAY-0112
• SYSFUND-0218
• DISPLAY-0063
• DISPLAY-0095
已更新的Requirement
下列Requirement均已更新:
• GRAPHICS-0010. Restructure of details.
• CONNECT-0120. Republished.
• NETMEDIA-0002. Clarification.
• NETMEDIA-0008. Added "if-implemented."
• NETMEDIA-0011. Added "if-implemented."
• NETMEDIA-0017. Reworded exception.
• NETMEDIA-0021. Minor edits.
• NETMEDIA-0022. Clarification.
• NETMEDIA-0026. Clarification.
• NETMEDIA-0029. Clarification.
• NETMEDIA-0032. Clarification.
• NETMEDIA-0036. Removed "if-implemented," added clarification.
• NETMEDIA-0037. Clarification, added exception.
• NETMEDIA-0043. Clarification.
• NETMEDIA-0047. Removed "if-implemented," clarified exception.
• NETMEDIA-0049. Clarification.
• NETMEDIA-0053. Added regional profiles, clarified exceptions.
• NETMEDIA-0054. Removed "if-implemented."
• NETMEDIA-0059. Clarification.
• NETMEDIA-0060. Changed to "if-implemented."
• NETMEDIA-0061. Clarification.
• NETMEDIA-0066. Removed "if-implemented," added exception.
• NETMEDIA-0078. Changed to "if-implemented."
• PORTABLE-0036. Clarification.
• NETMEDIA-0001. Clarification.
• NETMEDIA-0003. Clarification.
• NETMEDIA-0008. Clarification.
• NETMEDIA-0018. Exemption clarified.
• NETMEDIA-0041. Clarification.
• NETMEDIA-0042. Clarification.
• NETMEDIA-0048. Clarification.
• NETMEDIA-0050. Clarification.
• NETMEDIA-0051. Clarification.
• NETMEDIA-0062. Clarification.
• NETMEDIA-0070. Clarification.
• NETMEDIA-0071. Clarification.
• NETMEDIA-0072. Clarification.
• STREAM-0084. Fixed typo.
• BUSPORT-0041. Changed effective date to June 1, 2012.
• SYSFUND-0192. Clarified intent on allowing only Windows 7 logo drivers on Windows 7 systems.
• CONNECT-0123. Clarified meaning of "alternate."
• NETWORK-0212. Changed effective date to January 1, 2011 for client devices.
• NETWORK-0227. Changed effective date to January 1, 2011. Added clarification.
• BUSPORT-0045. Deleted portion of text about CSZ bit.
• DEVFUND-0039. Fixed typo.
• DEVFUND-0048. Clarification.
• STORAGE-0026. Clarification.
• CONNECT-0034. Deleted section 5.
• BUSPORT-0042. Changed effective date to June 1, 2012.
• DISPLAY-0069. Restructured for clarity.
• GRAPHICS-0007. Restructured for clarity.
• GRAPHICS-0015. Updated title and added details.
• GRAPHICS-0031. Restructured for clarity.
• GRAPHICS-0036. Restructured for clarity.
• GRAPHICS-0071. Restructured for clarity.
• DISPLAY-0105. Added detail to design notes section.
• GRAPHICS-0074. Added detail to the WDDM driver checklist.
• GRAPHICS-0075. Added second paragraph.
• STORAGE-0001. Changed end of life for Medium Changer and Tape programs to June 1, 2010.
• STORAGE-0003. Clarifications, changed end of life for Medium Changer and Tape programs to June 1, 2010.
• STORAGE-0024. Updated note, superseded STORAGE-0017.
• STORAGE-0006. Clarification.
• STORAGE-0007. Clarification.
• BUSPORT-0019. Combined with BUSPORT-0020.
• DISPLAY-0111. Does not apply to network projectors. Text clarification.
• GRAPHICS-0016. Updated minimum color depth to 32 bpp.
• STREAM-0082, 0083, 0084, 0085. Changed enforcement date to December 1, 2010.
• INPUT-0067. Deleted references to Terminal Services.
• SYSFUND-0009. Same change as GRAPHICS-0016.
• SYSFUND-0185. Updated for Windows Home Server V2.
• GRAPHICS-0023. Restructured for clarity.[@more@]
來自 “ ITPUB部落格 ” ,連結:http://blog.itpub.net/21364747/viewspace-1036902/,如需轉載,請註明出處,否則將追究法律責任。
相關文章
- windows徽標鍵是哪個 windows徽標鍵的功能Windows
- 「Adobe國際認證」 Adobe Illustrator徽標設計
- 【乾貨分享】最新WHQL徽標認證申請流程
- 什麼是WHQL微軟徽標認證?為什麼需要這項認證?微軟
- 安信實驗室呼籲鍵盤廠商申請windows徽標認證(WHQL)Windows
- EMQX Cloud 更新:新增 Redis 和 JWT 外部認證授權MQCloudRedisJWT
- 2020全球資料安全標準和認證展望
- EMQX Cloud 更新:外部認證授權MQCloud
- CB認證執行標準
- Basic認證和Bearer Token認證的區別
- 如何使用 SAP API Portal Policy Editor 給 SAP API 呼叫自動新增認證資訊API
- 關於os認證和口令檔案認證(轉)
- Windows 11 WHQL認證的必要性Windows
- Linux 中國徽標徵集活動結果Linux
- drf-路由和認證路由
- 如何找到SAP Cloud for Customer標準培訓和認證方面的資訊Cloud
- 同屏器CE認證測試標準
- 細說API - 認證、授權和憑證API
- shiro授權和認證(四)
- 授權(Authorization)和認證(Authentication)
- Windows安全認證是如何進行的?[Kerberos篇]WindowsROS
- Linux 中國徽標徵集活動進展彙報Linux
- Linux 中國徽標徵集活動公開評選Linux
- Docker開啟TLS和CA認證DockerTLS
- Windows 11 & Server 2022 HLK kit WHQL認證注意事項WindowsServer
- 生成Github JS 倉庫的測試覆蓋率徽標GithubJS
- Windows下IIS部署自建CA證書進行雙向認證的過程Windows
- 選擇檢測機構,有CNAS認證和沒CNAS認證的區別
- 認證授權方案之JwtBearer認證JWT
- HTTP認證之基本認證——Basic(一)HTTP
- HTTP認證之基本認證——Basic(二)HTTP
- HTTP認證之摘要認證——Digest(一)HTTP
- SpringSecurity認證和授權流程詳解SpringGse
- Tomcat 容器的安全認證和鑑權Tomcat
- 理解OIDC協議和認證機制協議
- SGS授予方信電源UL 9540A國際標準認證證書
- 微軟宣佈Windows 10 Mobile更新四月版1803即將釋出:通過藍芽認證資訊微軟Windows藍芽
- 微軟宣佈Windows 10 Mobile更新四月版1803即將釋出:透過藍芽認證資訊微軟Windows藍芽
- 跟我一起學Go系列:Go gRPC 安全認證方式-Token和自定義認證GoRPC