Brocade 300 Access Gateway Quickstart Guide

快速設定Brocade 300 光纖交換機

兩種方法：
一，安裝EZSwitchSetup，透過交換機和com口用軟體配置,這個最簡單，建議用這種方式。

[@more@]

二，透過com啟動的時候用命令列連線。
1,配置終端連線
Bits per second: 9600
Data bits: 8
Parity: none
Stop bits: 1
Flow control: none

2,連線電腦，開啟終端連線，交換機加電：
預設使用者名稱：admin
預設密碼：password

交換機啟動過程：
The system is coming up, please wait...

U-Boot 1.1.3 (Jun 5 2008 - 23:49:03)

CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
No Security/Kasumi support
I2C boot EEPROM enabled
Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
Internal PCI arbiter enabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
Board: Tomahawk
I2C: ready
DRAM: Initializing DDRSDRAM
DDR Init: speed = 132000002
DQS calibration - Window detected:
max_passing_cases = 55
wr_dqs_shift = 89
dll_dqs_delay_X = 31
dll_dqs_delay_X window = 4 - 58
DDR0_09=0x00011d59
DDR0_22=0x0026790b
DDR0_17=0x1f006200
DDR0_18=0x1f1f1f1f
DDR0_19=0x1f1f1f1f
ECC Enabling
Start memory clearing @ 0x00000000 size = 0x20000000...addr = 0x10000000
addr = 0x20000000
DONE
512 MB
Now running in RAM - U-Boot at: 1fb43000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Tomahawk CFI Flash Driver Initialized
4 MB
ATA interface setup: io_base=0xf8f00000, port=0x1f0, ctl=0x3f6
PCI:
pci_pre_init : SDR0_SDSTP1 = a0000000
SDR0_DDRCFG = 0x000000d2
Skip our host bridge
00 07 1657 0011 0280 18
In: serial
Out: serial
Err: serial
Net:
Waiting for PHY auto negotiation to complete..... TIMEOUT !
done
ENET Speed is 10 Mbps - HALF duplex connection (EMAC0)
ppc_4xx_eth0 initialized

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test using Default POST RAM Test succeeded.

set_bootstatus: BS_LOAD_OS, platform_idx = 1

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot: 0
ATA device vendor STI Flash 8.0.0, product STI1M3d108218090428, revision 01/17/0
7
Map file at LBA sector 0x958bf
Number of fragments is 0x2
End dest point is 0x00685000.
## Booting image at 00400000 ...
Image Name: Linux-2.6.14.2
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 2637767 Bytes = 2.5 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 1561250 Bytes = 1.5 MB
Image 1: 1076503 Bytes = 1 MB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
## Current stack ends at 0x1FB01BE0 => set upper limit to 0x00800000
## initrd at 0x0057D2F0 ... 0x00684006 (len=1076503=0x106D17)
Loading Ramdisk to 1f9fa000, end 1fb00d17 ... OK
initrd_start = 1f9fa000, initrd_end = 1fb00d17
## Transferring control to Linux (at address 00000000) ...
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda1...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
uptime: 4293889102; sysc_qid: 0

Fabric OS (SW300)

SW300 console login: 2009/01/15-06:58:56, [HAM-1004], 2,, INFO, Brocade300, Proc
essor rebooted - Unknown
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
sysctrld: all services Standby
sec0: Security is initializing........
sysctrld: all services Active
2009/01/15-06:59:08, [EM-1049], 3,, INFO, Brocade300, FRU PS 1 insertion detecte
d.
POST1: Started running Thu Jan 15 06:59:09 GMT 2009
2009/01/15-06:59:10, [EM-1049], 4,, INFO, Brocade300, FRU Fan 1 insertion detect
ed.
POST1: Test #1 - Running turboramtest
2009/01/15-06:59:11, [EM-1049], 5,, INFO, Brocade300, FRU Fan 2 insertion detect
ed.
2009/01/15-06:59:17, [EM-1049], 6,, INFO, Brocade300, FRU Fan 3 insertion detect
ed.
POST1: Script PASSED with exit status of 0 Thu Jan 15 06:59:21 GMT 2009 took (0:
0:12)
POST2: Started running Thu Jan 15 06:59:22 GMT 2009
POST2: Test #1 - Running portloopbacktest (SERDES)
POST2: Running diagshow
POST2: Script PASSED with exit status of 0 Thu Jan 15 06:59:29 GMT 2009 took (0:
0:7)
2009/01/15-06:59:29, [BL-1000], 7,, INFO, SW300, Initializing ports...
2009/01/15-06:59:29, [BL-1001], 8,, INFO, SW300, Port initialization completed.

Fabric OS (SW300)

用預設使用者名稱登入：
SW300 console login: admin
Password:
Please change passwords for switch default accounts now.
Use Control-C to exit or press 'Enter' key to proceed.

Warning: Access to the Root and Factory accounts may be required for
proper support of the switch. Please ensure the Root and Factory
passwords are documented in a secure location. Recovery of a lost Root
or Factory password will result in fabric downtime.

修改使用者密碼：
for user - root
Changing password for root
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Please change passwords for switch default accounts now.
for user - factory
Changing password for factory
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Please change passwords for switch default accounts now.
for user - admin
Changing password for admin
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Please change passwords for switch default accounts now.
for user - user
Changing password for user
Enter new password:
Re-type new password:
passwd: all authentication tokens updated successfully
Saving passwords to stable storage.
Passwords saved to stable storage successfully
SW300:admin>

3，設定交換機ip
SW300:admin> ip
ipaddrset ipaddrshow ipfilter
SW300:admin> ipaddrset
Ethernet IP Address [10.77.77.77]:172.25.0.22
Ethernet Subnetmask [255.255.255.0]:255.255.0.0
Fibre Channel IP Address [none]:
Fibre Channel Subnetmask [none]:
Gateway IP Address [none]:172.25.0.254
DHCP [Off]:
IP address is being changed...Done.
SW300:admin>

SW300:admin> ipaddrshow

SWITCH
Ethernet IP Address: 172.25.0.22
Ethernet Subnetmask: 255.255.0.0
Fibre Channel IP Address: none
Fibre Channel Subnetmask: none
Gateway IP Address: 172.25.0.254
DHCP: Off
SW300:admin>

4,關閉交換機，連線網線，透過ip地址登入配置其他選項。