在倒數計時的時候，敲任意鍵進入boot模式，boot升級的好處是，即使當前版本是P3T1，你也可以直接升級為P1T3,如果是正常升級的話，得先升級到P4T3,才能繼續升級到P1T3。
enter into the shell..
bootShell made in Apr 26 2010 17:02:37
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>p 檢視帶外IP
The IP address: 192.168.1.2
The SubnetMask: 255.255.255.0
The MAC address: 00-1E-73-92-C5-B2
The TFTP HOST IP address: 192.168.1.247
The UDP HOST IP address: 255.255.255.255
The Gateway IP address: 0.0.0.0
[M24E]/DATA/version/M24E>c 修改帶外IP
board work type 1 is invalid
change to default 1
The IP address: [192.168.1.2] 192.168.1.2
The SubnetMask: [255.255.255.0]
The MAC address: [00-1E-73-92-C5-B2]
The TFTP HOST IP address: [192.168.1.247] 192.168.1.147
The Gateway IP address: [0.0.0.0]
The Board WorkType: [1]
Save new value...shell set board work type 1
bootline =eth(0,0):-mmsp.axf,-cm24e.bin e=192.168.1.2 h=192.168.1.147
ok!
ok!
eth0, the new ip = 192.168.1.2, new mask = 255.255.255.0
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>burn bm24e.bin 升級控制交換板的boot程式
Start downloading the program................Done!
Begin burning bootrom........Done!
Ok
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>downver m24e.bin m24e.bin m24e 升級控制交換板的程式m24e.bin
Start downloading Program..............................
...............................Done!
/DATA/version/M24E\m24e.bin
... ...
Version download success.
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>downver m24e_sv.bin M24E_SV.bin m24e 升級窄帶韌體程式m24e_sv.bin
supportMultiVersions[D://f822_v110_p1t1//code//9806//RSL//R320//source//verconfig.c:319] : [M24E_SV.bin] is another fnctType fname of m24e
Start fetching m24e_sv.bin from TFTP server...
MAC[0]:0
MAC[1]:1e
MAC[2]:73
MAC[3]:92
MAC[4]:c5
MAC[5]:b2
Got ARP
Filename 'm24e_sv.bin'.
Load address: 0x100000
Loading: *
################################
Bytes transferred = 1610676 (1893b4 hex)
isLocalValidExtraVerType[D://f822_v110_p1t1//code//9806//RSL//R320//source//verconfig.c:670] : The name of the version is not ExtraVer
/DATA/version/M24E\M24E_SV.bin
remove old file /DATA/version/M24E\M24E_SV.bin ok
Now writing into file...
..................................................................................................Done!
version download success.
[M24E]/DATA/version/M24E>setactver m24e M24E.bin 設定新版本為主用版本
ok
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>
[M24E]/DATA/version/M24E>reboot
?
boot shell start!
ucHandle=0
ucBusWidth=0x2
fdev->Desc.VendorID=0x0001
fdev->Desc.DeviceID=0x007e
It's CFI-compliant.
Erase block regions number=1
Region[0]: Size=0x00020000 Count=128
uiCmdType=0x00000002
now,MaxBytesEachWrite=0x00000020
Flash Open OK.
TFFS device create success!
Flash is OK!
bootline =eth(0,0):-mmsp.axf,-cm24e.bin e=192.168.1.2 h=192.168.1.147
init network...
MAC[0]:0
MAC[1]:1e
MAC[2]:73
MAC[3]:92
MAC[4]:c5
MAC[5]:b2
done!
checking CPLD updata file...
CPLD updata not supported.
Press Enter key to stop auto-boot...
checkAllDirs
/DATA/ - disk check in progress ...
dosChkLib : CLOCK_REALTIME is being reset to MON JAN 31 19:39:52 2000
Value obtained from file system volume descriptor pointer: 0x59fe5d4
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/DATA/ - Volume is OK
total # of clusters: 1,940
# of free clusters: 769
# of bad clusters: 0
total free space: 6,152 Kb
max contiguous free space: 6,299,648 bytes
# of files: 5
# of folders: 10
total bytes in files: 9,237 Kb
# of lost chains: 0
total bytes in lost chains: 0
auto-booting...
active version specified
VerFile: /DATA/version/M24E\M24E.bin VerSize = 7848193
inflate success.
ARM1 (CSP) booting at 0x01001000 ...
VerFile: /DATA/version/M24E\M24E_SV.bin VerSize = 1610676
Downloading MSP Image from 0x0586C01C ...
code_offset=0x80
code_base=800000
data_offset=186530
code_size=1864b0
data_base=9864b0
data_size=110
zeroinit_base=9865c0
prog_entry=100
AIFHEADER:
BL_DecompressCode=e1a00000
BL_SelfRelocCode=e1a00000
BL_DbgInitZeroInit=eb00000c
EntryPointOffset=ff800100
ProgramExitInstr=ef000011
ImageReadOnlySize=1864b0
ImageReadWriteSize=110
ImageDebugSize=251c
ImageZeroInitSize=11324
ImageDebugType=23241
ImageBase=800000
WorkSpace=0
AddressMode=20
DataBase=0
FirstFatOffset=188b5c
Reserved2=0
DebugInitInstr=e1a00000
ZeroInitCode[0]=e04ec00f
After csm_download_data
After csm_download_fat
After csm_zero_init
Booting ARM0 (MSP) at 0x00000100 ...
init config ...... OKold cpld value is 0x2b, new value is 0x2b
PCI unit 0: Dev 0xb024, Rev 0x11, Chip BCM56024_B0, Driver BCM56224_B0
PCI OK: VEC=39, 0, 39SOC unit 0 attached to PCI device BCM56024_B0
init BoardInfo ...... OK
init packet ...... OK
init port ...... OK
init vlan ...... OK
init Trunk ...... OK
init L2 ...... OK
init Qos ...... OK
init Pvlan ...... OK
init Mirror ...... OK
init Mcast ...... OK
init Stats ...... OK
init Pvc ...... OK
sspSystemInit all success!!!!!!
BCM.0>
init taskid is 69ffe68BOOT_LINE:eth(0,0):-mmsp.axf,-cm24e.bin e=136.1.1.100 h=136.1.1.1
Host Name: bootHost
Target Name: vxTarget
User: target
ifIndexLibInit
muxDevLoad
parse: Unit = 0
parse: ivec = 1
parse: ilevel = 1
vedReset : entry
vedConfig : entry
parse: Unit = 1
parse: ivec = 1
parse: ilevel = 1
vedReset : entry
vedConfig : entry
endFindByName
Attached TCP/IP interface to eth unit 0
usrNetIfAttach lo
Attaching network interface lo0... done.
enter usrNetIfConfig
ifMaskSet, ifname = lo0, netmask = 0x0, devName = lo, unitNum = 0, inetAdrs = 0x106edbc
ifAddrSet, ifname addr = 0x0x69ff9646103b58, inetAdrs ad (dr = 0xtNetTask69f): f97cPin:
85hostA out of range,dd
85us,rNetIfConfig
0enter
usrNetIfConfig
ifMaskSet, ifname = eth0, netmask = 0x0, devName = eth, unitNum = 0, inetAdrs = 0x69ffb4c
ifAddrSet, ifname addr = 0x69ff964, inetAdrs addr = 0x69ff97c
vedMCastAdd(0) : entry for MAC 0x1 0 0x5e 0 0 0x1
vedConfig : entry
vedAddrFilterSet : entry
hostAdd
Adding 43617 symbols for standalone.
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003
CPU: Chagall. Processor #1.
Memory Size: 0x5a00000. BSP version 1.2/0.
WDB Comm Type: WDB_COMM_NETWORK
WDB: Ready.
-> TFFS device create success!
oamPrintSelect not oam user, change take effect when switchToOam!
-> shell restarted.
[registerMPUnitMode]: The Input UnitName has been registered!!
parse: Unit = 2
parse: ivec = 1
parse: ilevel = 1
vedReset : entry
vedConfig : entry
Begin to add default narrowband data...
Add default RACK data...OK!
Add default SHELF data...OK!
Add default SCCB data...OK!
Add default VOPC data...OK!
Add default ATLC data...OK!
Add default MGC data...OK!
Add default VOIP data...OK!
Add default MG data...OK!
Add default IPS_TERMID data...OK!
Add default SLC_TERMID data...OK!
[registerMPUnitMode]: The Input UnitName has been registered!!
[registerMPUnitMode]: The Input UnitName has been registered!!
IFX TAPI, version 4.2.1.0, (c) 2001-2008 Infineon Technologies AG
IFX VINETIC-xT device driver, version 1.0.3.0, (c) 2007-2008 Infineon Technologies AG
Board Setup complete.
device 0 on
device 0 Object done
device 0 boot done
device 0 initvcp suc
dev 0 hard ver 4
dev 0:ChkSum=0x36a34d41,Rev=0x207,Id=0x14,Major=0x0,Minor=0x1
Initializing DVP 0...device 0:VP_DEV_EVID_DEV_INIT_CMP:0x3f
SLC fopen /VERSION/M24E/SlcData.txt errno 0x380003
Setting events masks...0
dev 0 set flash:90,380
dev 0 init vcp completed
LocalCallMgt Get MpMasterPowerOnEvent!
VtcaSunitHand Get MpMasterPowerOnEvent!
MptDebugEvent recv!
cmd 3, unit 1, sunit 1, startChannel 0,
channelNum 24, reason 0
UnBlockSunitByNum
exscanTask_INIT: OK
PowerTask_INIT: OK!
comTask_INIT: OK!
comydtTask_INIT: OK!
Load agcmd file...OK!
cordump Get MpMasterPowerOnEvent!
UnitHand power on
start execute profile!
finish execute profile!
[NOTE]: Port 3/1 link up
######################################################################
# #
# Welcome to ZTE Full Service Access Platform #
# #
# Press Return to get started #
# #
# Copyright 2005-2009 , ZTE Co.,Ltd. #
# #
######################################################################
Login:admin
Password:
[NOTE]: User "admin" Log in with Console
ZXAN>en
Please input password:
ZXAN# show version
CardType Type VerNo VerLen Status BuildTime State FileName
--------------------------------------------------------------------------------
M24E MVER V1.1.0P1T3 7847937 VALID 20100609165848 active M24E.bin
M24E SVER V1.1.0P1T3 1610420 VALID 20100426181413 active M24E_SV.bin
Current Boot Info:
M24E BOOT V1.1.0P1T3 367840 VALID 20100426170253 active
Current Chip Info: 0X0000000A